Wisdom On Fiat Panda Key Fob Replacement From A FiveYearOld
Reasons Your Fiat 500 Key Fob Won't Work
A key fob for the Fiat 500 is a handy way to unlock the doors and get started the car. There are a myriad of reasons why the fob may stop working. These include a dead battery, damage to the receiver module, issues, and interfering.
This listing is for an NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It must be professionally programmed (click here to search for local automotive locksmiths). It includes lock, unlock, and trunk buttons.
Dead Coin Battery
The most frequent reason that your 500 key fob will not function is the battery is dead. Modern key fobs have an operating range that is limited and must be within a few inches of the vehicle to function. If you're far from your vehicle and you press the key fob button the car won't respond, and will display a "Key Fob Not Detected" message in the instrument cluster.
If this happens, replace the battery of your coin cell (Part number CR2032) by a new one from a reputable manufacturer like Panasonic, Duracell, or Energizer. They are typically available in your local hardware store or online.
After you've replaced the coin cell battery, you can test it by standing in front of your Fiat 500 and pressing the buttons. The car should flash its parking lights and the key fob should operate the lock and unlock switches.
If your key fob isn't working after replacing the battery, it may be water damage that is preventing it from communicating with the module inside your vehicle. Water damage can happen in many ways, including the simple splash or submerging the key fob into saltwater at the beach. If you suspect that your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture back out. If this does not work, you'll have to get your fob changed by an auto locksmith or dealer.
Water Damage
Damage to the water supply can occur if you immerse the fob in the ocean or wash it in a washer. Saltwater can cause the circuit board to short and then fail. It's not a good thing to soak the fob in water however, but don't give it up in the event that you accidentally drop it in the water or don't take it out of your pants pocket.
First remove the battery from the fob. Clean the electronic chip with isopropyl or a similar product and then dry it completely before replacing the battery. Test the fob next to determine if it's functioning. If the key doesn't function, it may need to be reprogrammed. This is usually done by an auto locksmith or dealer.
If the key is more recent and has never been programmed to your car it is likely to need to be replaced completely. A professional locksmith in the automotive industry can do this job. The locksmith will need the key to be cut to match the car's ignition. The locksmith will also have to program your fob into the vehicle's system. It's a simple and cost-effective process which can be completed on the next day.
Receiver Module Issues
One of the most common reasons your 500 key fob won't be working is that it's simply out of range. The remote usually has a range of 30 feet or less, and if it's too far from your vehicle, it won't respond to your commands. You can easily remedy this by moving your remote closer to your vehicle until it responds.
If your fob does not work after you replace the coin battery, also called a "button", "watch" or "button" or "button", it could be due to an issue with the internal circuit board. In Click At this website , reprogramming the fob will fix the problem. There are instructions on how to do this for most automobiles by searching YouTube or looking through the owner's manual.
It is possible to replace the clips made of metal that hold the coin batteries in place. If they loose tension, it can stop your coin battery from sitting properly, causing your remote to malfunction.
In rare cases the fob could be out of alignment with your vehicle because of hardware or software issues. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances it is possible that the software will require reinstallation into your body control modules.
Interference
Interference can also cause the key fob not to receive or transmit signals. This can happen when the key fob is near a radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. The key fob may not function because of a problem to the buttons, water damage or damage to the internal chips.
If the key fob been unable to function for a while without notice or after trying everything you can do at home to resolve it e.g. replacing the battery, reprogramming, and using the spare key fob, you might have a damaged receiver module on your 500. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.
Fortunately, there's an easy way to reset all of the onboard systems in your 500 device, including the key fob. Disconnect the battery of 12 volts for about 15 minutes by disconnecting the negative cable first then the positive cable. Then, reconnect the battery. This will eliminate any remaining electrical charge and restart the car's computers, which could allow you to the key fob to function again. If the issue persists, you should seek out an expert technician. They can identify the exact cause of problems.
