Instructions Of Interior Painting

Inside painting requires as careful preparation of surfaces as does external painting. The arrival of odorless paints now makes it possible to paint any time of the entire year. Formerly, most interior painting in the home was done in the tumble or spring, when it was possible to leave the windows open to ventilate the room. But open windows brought dust particles into the room to mar the finished painted surface.

An excellent interior paint job is frequently 50% planning and 50% painting. Usually do not rush in preparing the areas in your eagerness to get at the brush or roller. If you do not prepare the surfaces properly, you will be back with the color brush or roller in a couple of months.

In this section you will find the necessary information on the use of different types of paints on various interior walls, ceiling and floor materials.

Plaster

New dry plaster in good shape, which is to be finished with a paint apart from water paint, should be given a coat of primer-sealer and allowed to dry thoroughly before getting inspected for uniformity of look. Variations in gloss and color differences in the case of tinted primers indicate set up whole surface has been totally sealed. If not, another coat of primer-sealer should be applied. If only a few "suction spots" are apparent, another coat over these areas may be sufficient.

A set, semi-gloss, or high-gloss finish could be applied to the primed surface. For a flat finish, two coats of flat wall color should follow the priming coat. For a semi-gloss surface finish, one coat of flat walls paint and something coat of semi-gloss paint ought to be applied to the primed area. For a high-gloss surface finish, one coat of semi-gloss paint and something coat of high-gloss enamel ought to be used over the priming coat.

Before applying water paints of the calcimine variety to new plastered walls they must be sized, using the glue-water dimensions or, if the plaster will be dry, a thin varnish or primer-sealer.

Cold water paints of the casein variety may be applied either directly to a plastered surface, or the surface could be first given a layer of primer-sealer to equalize uneven suction results. The same will additionally apply to resin-emulsion paints, with the suggestions of the manufacturer of the product being given preference in the event of doubt. Since resin-emulsion paints generally contain some essential oil in the binder, they ought to ordinarily be applied only to plaster which includes dried thoroughly.

Texture wall paints may also be used on plaster surfaces. The benefits of this sort of paint are that one coat economically produces a textured decoration and relieves the monotony of smooth flat paint. It also addresses cracks or patches in the plaster considerably more completely than ordinary wall paint. The negatives of texture wall paint are they Collect dust and are difficult to revive to a smooth finish. These materials can be found as water-or oil-based paints, will be thicker than ordinary wall paints, and could be applied to wallboard as well as plaster to produce textured effects such as random, Spanish, mission, and multicolored.

Composition Wallboard

Composition wallboard usually presents no particular painting problems if the normal precautions are observed, such as making certain that the top is dry and clear of grease and essential oil. The painting procedure for wallboard is the same as for plaster; it requires a priming and sealing coat accompanied by whatever finishes coats are wanted, or could be given one-coat flat or resin-emulsion type paint.

Franklin Painters NJ 07416 Wallpaper

Water-thinned paint may be put on wallpaper that's well- bonded to the walls and does not contain dyes which may bleed into the paint. One thickness of wallpaper is usually preferable for color application. Paints other than those of the water-thinned type can also be applied to wallpaper by following a instructions given for painting plaster. Even so, wallpaper coated with this type of paint is difficult to remove without injury to the plaster.

Wood Walls and Trim

New interior walls and lumber trim should be smoothed with sand-paper and dusted before painting or varnishing. To preserve the grain of the timber, the surface could be rubbed with linseed oil, varnished or shellacked, and waxed. If an opaque finish off is desired, semi-gloss color thinned with 1 pint of turpen-tine per gallon of paint or the primer-sealer previously described for walls can be utilized as a priming coating on wood. A couple of coats of semi-gloss paint should then be applied on the thoroughly dry prime layer, or in case a full-gloss finish is desired, the last coat ought to be a high-gloss enamel.

Masonry Walls and Ceilings

Interior masonry wall space and ceilings above grade may, generally, be painted in much the same manner as plaster surfaces. In this article again, it is necessary to permit adequate moment for the masonry to dried out before applying paint and, furthermore, attention should be directed at the preparation of the top. When decorating a walls containing Portland cement (concrete, for example), it is vital to take precautions against the attack of alkali. For this purpose, alkali-resistant primers such as for example rubber-base paints can be utilized when oil paints are to check out.

Cement-water paints are suitable for application to basement walls which are damp because of leakage or condensation. To use these paints, the same procedure should be followed as is described right here for painting exterior masonry surfaces.